Table of Contents
Introduction................................................................................................................................5
Unpacking your system .............................................................................................................5
Installation..................................................................................................................................5
Basic Instructions.......................................................................................................................5
Buttons and LCD...................................................................................................................5
Hardware Description............................................................................................................6
Main Menu.................................................................................................................................7
Functions ...................................................................................................................................8
Copy......................................................................................................................................8
Test........................................................................................................................................8
Test & Copy...........................................................................................................................8
Verify .....................................................................................................................................9
Compare................................................................................................................................9
Prescan .................................................................................................................................9
Disc Info ................................................................................................................................9
Edit Track ............................................................................................................................10
CD to CD Edit .................................................................................................................10
Close Session.................................................................................................................11
Setup .......................................................................................................................................12
Language ............................................................................................................................13
CD Burn Speed ...................................................................................................................13
Read Speed ........................................................................................................................13
Auto Start Drive...................................................................................................................13
Startup Menu.......................................................................................................................13
Auto Verify...........................................................................................................................13
Auto Compare .....................................................................................................................13
Auto Prescan.......................................................................................................................13
Eject Disc ............................................................................................................................13
Burn Mode...........................................................................................................................13
Display Time........................................................................................................................14
Button Sound.......................................................................................................................14
Device Info ..........................................................................................................................14
System Info .........................................................................................................................14
Quick Erase.........................................................................................................................14
Full Erase ............................................................................................................................14
Adv Setup ...............................................................................................................................15
UnderRun Protect................................................................................................................16
Overburn .............................................................................................................................16
Read Error Skip...................................................................................................................16
Burn-in.................................................................................................................................16
Update Firmware.................................................................................................................16
Compare Firmware..............................................................................................................16
H/W Diagnostic....................................................................................................................16
Load Default........................................................................................................................16
CD+G ..................................................................................................................................17
ISRC & MCN .......................................................................................................................17
USB Option .........................................................................................................................17
CD Text ...............................................................................................................................17
Disc Counter........................................................................................................................17
Update Drive F/W................................................................................................................17
Specifications – QD-MultiDrive Series ....................................................................................18
Technical Support....................................................................................................................18
Appendix 1 List of Functions ...................................................................................................19
Appendix 2 LCD Messages.....................................................................................................20
Audio Editing: ......................................................................................................................20
Firmware Update:................................................................................................................20
3
4
Introduction
The QD-MultiDrive Series includes the QD-123, QD-125, and QD-127. Each is a high speed,
low cost CD Recordable duplication system from Microboards Technology, LLC.
The QD-MultiDrive is perfect for any user requiring easy copying of audio, video, or Data
CDs. Superior technology allows the QD-MultiDrive to ship without a hard drive. LED
indicators provide the user with status of the duplication process, minimizing the number of
faulty discs. Current high speed CD Recordable technology is supported at 52X, which is the
highest in the industry. Applications suited for the QD-2 include Pro Audio, Multimedia,
Government / Education, Software Development, Medical Imaging, and Data Interchange.
Unpacking your system
When unpacking your duplicator, confirm the following items are included:
•
•
•
•
QD-MultiDrive duplicator
Power cable
Manual
CD-R disc
If any of these items are missing, please contact Microboards Technology Technical Support.
IMPORTANT: Please keep all the packing for your QD-MultiDrive duplicator. If your
unit ever needs to be sent in for service, it must be returned in the
original packing or the warranty will be voided.
Installation
•
Connect the power cable to the QD-MultiDrive duplicator and plug in to a protected
power outlet strip or UPS power supply.
Note for Installation:
1) The socket outlet shall be installed near the equipment and be easily
accessible.
2) Do not block cooling fans.
•
•
•
Turn on power to the duplicator.
The system will go through initialization and then display: 1. Copy.
The system is now ready to use.
Basic Instructions
Buttons and LCD
There are four buttons and an LCD on the front panel of the QD-MultiDrive duplicator.
LED display: Shows the menu items and any status messages that may come up during
operation
ENT button: The ENT button, used to start a duplication process or enter into an area in the
menu structure.
ESC button: The ESC button, used to stop an operation or move up the menu structure.
▲ button, used to scroll up in the different menus.
▼ button, used to scroll down in the different menus.
5
Hardware Description
Controller Interface
Reader Drive
Recorder Drives
Power Switch
QD-123
Power LED
The QD-MultiDrive system consists of a CD reader, 3, 5, or 7 CD recorders (based on model)
and Controller module.
The master discs always go into the TOP CD Reader drive.
The blank CD media will always go into the CD Recorder drives below the Reader.
The power switch and power LED are also located on the front of the QD-MultiDrive
duplicator.
The LCD display will show the different menu selections and also information pertaining to
the recording process. Here is a typical example of what is displayed during the COPY
process:
Displays the function being performed,
Shows the percentage
such as Copying or Testing, and shows
completed for this action.
the record speed.
Copying – 52x
150.4 MB
17%
01:15
Displays the amount of data left to be
recorded. This number starts at the capacity
of the master and counts down.
Shows the time remaining to
complete this action. This
number also counts down.
6
Main Menu
ENT
Load Next
Blank Disc
Source Disc
Analyzing….
Copying–52x 17%
150.4MB 01:15
1.0 Copy
OK: 07
1.0 Copy
ENT
ENT
ESC
▼
Load Next
Blank Disc
ENT
Source Disc
Analyzing….
Testing–52x 17%
150.4MB 01:15
2.0 Test
OK: 07
2.0 Test
ESC
▼
Load Next
Blank Disc
ENT
ENT
Source Disc
Analyzing….
Copying–52x 17%
150.4MB 01:15
3.0 Copy
OK: 07
3.0 Test& Copy
ESC
▼
ENT
Copied disc is now
being read.
4.0 Verify
OK: 07
4.0 Verify
Preparing…...
Preparing…..
ESC
▼
ENT
Copied disc is now
being compared with
the master dis.c
Compare
Fail: 0
OK: 7
Diff: 0
5.0 Compare
ESC
▼
ENT
ENT
Source Disc
Analyzing….
Scaning 24x 15%
6.0 Prescan
PreScan OK
620.4MB
01:15
ESC
▼
▼
▼
▼
▼
Source Disc
Analyzing….
Total01 Sessions
Total01 Tracks.
Total: 04:15
Total: 37.0 MB
Session01
Track01 - 01.
Track01
CDXA37.1 MB
7.0 Disc Info
▼
ENT
ESC
8-01. Edit Track
CD to CD Edit
Select Track:
8.0 Edit Track
1/10
05:14
ENT= Select that track number
ENT or
▼
= Skip that track number
▼
Select Track:
+10/10 05:14
▼
Select Track:
End 3 Trk 13:36
ENT
NO
YES
ESC
YES
End Edit disc
And burn? YES
Copying– 52x Edit
3/10 ? 2/3
Burn Complet!e
OK: 01
Continue edit
Next Disc? NO
▼
Insert Next Master
NO
Close all disc’s
Session?YES
▼
ENT
Closing Sesion
Please wait…..
ESC
Close Complete
OK: 7
Fail: 0
NOTE: This feature is not available on all models.
The reader drive must have a headphone jack for
this feature to operate.
ESC
ESC
ENT
ENT
YES
8-02. Edit Track
Play Audio Track
Select Track:
1/16 02:45
Playing Track– 1
00:15
/
02:45
▼
ESC
ENT
8-03. Edit Track
Close Session
Close all Disc’s
Sessions? YES
Closing Session
Please wait…...
Close Complete
OK: 7
Fail: 0
NO
See the
Setup Menu
(page12)
9. Setup
Press and Hold the ESC
button for3 seconds
See the Adv.
Setup Menu
(page15)
10. Adv Setup
7
Functions
There are 9 different functions for the QD-MultiDrive duplicator: Copy, Test, Test & Copy,
Verify, Compare, Prescan, Disc Info, Edit Track and Setup. For the Setup options, please
refer to page 12.
These instructions refer to using 7 recorder drives (available only in the QD-127), but the QD-
MultiDrive will operate using any number of the available recorder drives.
Copy
Please refer to pages 15-17 for CD+G duplication
The Copy function is used to copy our master disc to the blank media, CD-R or
CD-RW. The QD-MultiDrive duplicator will be in Copy mode when it is turned
on. The display will read:
1. Copy
Place your master disc into the CD reader drive.
Place your blank media into the CD Recorder drives.
Copying – 52x
150.4MB
18%
01:15
Press the ENT button on the controller interface.
The data will now be copied to the blank discs.
When the job is completed, the recorded discs will be ejected from the
recorder drives. The display will read:
1.0 Copy
OK: 07
Test
The Test function is used to simulate copying our master disc to the blank media,
CD-R or CD-RW. To use the Test function, press the ▼ button on the controller
until Test is displayed:
2. Test
In Test mode, the blank media will remain blank and can be used again.
Place your master disc into the CD reader drive.
Place your blank media into the CD Recorder drives.
Testing – 52x
150.4MB
18%
01:15
Press the ENT button on the controller interface.
The duplicator will now simulate writing to the blank discs.
When the job is completed, the recordable discs will be ejected from the
recorder drives. The display will read:
2.0 Test
OK: 07
Test & Copy
The Test and Copy function will perform both operations, one after the other. If the Test
portion passes without errors, the system will automatically start the Copy process.
3. Test & Copy
To run the Test and Copy function, press the ▼▲ buttons until the
display reads:
Place your master disc into the CD reader drive.
Place your blank media into the CD Recorder drives.
Press the ENT button on the controller interface.
Testing – 52x
150.4MB
18%
01:15
The duplicator will now simulate writing to the blank discs.
8
Copying – 52x
150.4MB
18%
01:15
When this operation completes, the unit will start the Copy
process:
3.0 Copy
OK: 07
When the job is completed, the recorded discs will be ejected from the
recorder drives. The display will read:
Verify
The Verify function will check to see if the recorded disc can be read. This is different from
the Compare function. The Verify function will not compare itself with the master disc. It is
only checking to see if the disc that was recorded can be read back.
To run the Verify function, press the ▼▲ buttons until the display reads:
4. Verify
Place the copied discs into the CD Recorder drives.
Press the ENT button on the controller interface.
4. Verify
OK: 07
The copied discs will now be read. Once completed, the display will show:
Compare
The Compare function is used to compare the master disc with the copied disc. The
Compare function will only work with Data masters. If your master disc has audio or video
(VCD) on it, the Compare function will not work.
5. Compare
To use the Compare function, press the ▼▲ buttons until the display reads:
Place your master disc into the CD reader drive.
Place your copied discs into the CD Recorder drives.
Press the ENT button on the controller interface.
Compare
Fail: 0
OK: 7
Diff: 0
The duplicator will now compare the master and copied discs.
When completed, the display will read:
Press the ▼ button and the following screen will appear:
Src:01
CD-RW
Total: 15.2MB
Press the ▼ button again and the following screen will appear,
displaying the status of the first drive:
Tgt: 00
CD-RW
Identical
Press the ▼ button again to check the status of the second
drive, and again for the third.
Prescan
The Prescan function is used to verify the master disc can be read correctly.
To use the Compare function, press the ▼▲ buttons until the display reads:
6. Prescan
Place the master disc into the CD reader drive and press ENT.
Scaning – 24x 15%
620.4MB 02:15
The prescan starts and the following screen appears:
PreScan OK!
Once the scanning is complete, the following screen will appear:
Disc Info
The Disc Info function displays information on the type of master disc placed in the TOP
reader drive.
7. Disc Info
To use the Disc Info function, press the ▼▲ buttons until the display reads:
9
Place the master disc into the TOP reader drive. Press the ENT button. The source is
analyzed.
The following screen appears:
Source Disc
(Analyzing)
The following 4 screens display a variety of information about the master disc. The screens
are reached by pressing the ▼▲ buttons.
Total 01 Sessions
Total 01 Tracks
Total: 04:15
Total: 37.0MB
Session 01
Track 01 - 01
Track 01
CDXA 37.0MB
Edit Track
The Edit Track function allows you to select multiple tracks from different master discs and
place them on one Audio CD. The maximum number of tracks that can be written to the CD
is 99. In the Edit Track function, there are three options: CD to CD Edit, Play Audio Track
and Close Session. Play Audio Track will not apply if the drives do not have headphone
jacks on the front drive panels.
Important Note: The CD+G value must be set to OFF in order to use the Track Extraction
feature. Please see the Adv. Setup menu on page 15-17 for more details.
CD to CD Edit
To use the CD to CD function, press the ▼▲ buttons until the
display reads:
8. Edit Track
Press the ENT button. The following screen appears:
8-01. Edit Track
CD to CD Edit
1. Place the first master audio CD into the CD reader drive. Place the blank CDs into the
recorder drives. Press the ENT button.
The following screen appears:
Select Track:
1/16
04:53
2. To select a track that you want to burn to the blank disc, press
the ENT button. This will put a + symbol in front of that track:
Select Track:
+ 1/16 04:53
3. Press the ▼▲ buttons to scroll through the tracks on that CD, selecting the tracks you
wish to record.
4. Once all of your tracks are selected for that master, press
Select Track:
End 1Track 04:53
the ▼ button until the display reads:
This screen shows the total number of tracks selected from the master disc and the total time
of those tracks.
End Edit Disc
And burn? YES
5. Press the ENT button. The following screen appears:
Note: Pressing the ▼ button and selecting NO takes you
back to Editing tracks.
Copying – 52x Edit
1/16 → 1/1
6. Press the ENT button to begin recording the selected tracks
to the blank disc. The following screen appears:
7. Once the tracks are copied to the blank discs, the following
screen appears:
Burn Complete!
OK: 07
10
8. Press the ESC button to take you to this screen:
Continue Edit
Next disc? NO
If you wish to continue to add more audio tracks to the disc in
the recorder drive, press the ▼ button to change the NO to YES.
Then press Enter.
The TOP reader drive will open and ask you to put in the next master disc. Place the new
disc into the drive and close the tray. Go to step 3 and repeat the process.
Once you have completed copying the audio tracks to the Recorder drives, you will need to
close the discs.
Continue Edit
Next disc? NO
9. At this screen, leave the selection as NO and press ENT:
Close all disc’s
Sessions? Yes
Once ENT is pressed, the following screen appears:
Closing Session
Please wait….
10. Press the ENT button. The following screen appears:
Close Complete
Once the discs are closed, the following screen appears:
OK: 07
Fail: 00
Close Session
The Close Session function is used only if you did not close an audio CD, as described in the
Edit Track / CD to CD Edit section. You can use this function to manually close the disc.
To use the Close Session function, press the ▼▲ buttons until the
display reads:
8. Edit Track
8-01. Edit Track
CD to CD Edit
Press the ENT button. The following screen appears:
8-03. Edit Track
Close Session
Press the ▼ button until the display reads:
Make sure your recorded audio CDs are in the Recorder drives.
Press the ENT button. The following screen appears:
Close all disc’s
Sessions? Yes
Closing Session
Please wait….
Press the ENT button. The following screen appears:
Once the discs are closed, the following screen appears:
Close Complete
OK: 07
Fail: 00
11
Setup
ENT
▲
▼
▲
▼
ENT
ENT
ENT
9-01. Setup
Language
Language
English
Idioma
Spanish
Dil
TURKCE
9.Setup
▼
CD Burn Speed
Available speeds: 48x, 40x, 32x,
24x, 20x, 16x, 10x, 4x
▲
▼
9-02. Setup
CD Burn Speed
CD Burn Speed
Maximum
ESC
▼
Read Speed
▲
▼
9-03. Setup
Read Speed
Read Speed
Maximum
DVD Read Speed
limited to 16x and 8x.
Available speeds: 48x,
48x, 40x, 16x, 8x
▼
▲
▼
ENT
ENT
ENT
ENT
9-04. Setup
Auto Start Drive
Auto Start Drive
OFF
Options are Off,
1 and 2
Note: Option 2 is not used
in the QD-DVD 123 duplicator
ESC
▼
Options are Copy, Test. Test & Copy,
Verify, Compare, Prescan, Disc Info,
Edit Track, Setup, Adv Setup
▲
▼
9-05. Setup
Start Up Menu
Start Up Menu
1.Copy
▼
▲
▼
9-06. Setup
Auto Verify
Auto Verify
OFF
Options are ON
or OFF
▼
▲
▼
9-07. Setup
Auto Compare
Auto Compare
OFF
Options are ON
or OFF
▼
ESC
▲
▼
ENT
ENT
9-08. Setup
Auto Prescan
Auto Prescan
OFF
Options are ON
or OFF
▼
9-09. Setup
Eject Disc
Eject Disc
Eject Good Only
Eject Disc
Eject All Discs
Eject Disc
Do Not Eject
▼
▼
▼
▼
ENT
ENT
ENT
ENT
9-10. Setup
Burn Mode
Setup
DAO
Setup
TAO –Not Close
Setup
TAO
▼
▼
ESC
▲
▼
9-11. Setup
Display Time
Display Time
Off
Options are ON
or Off
▼
▲
▼
9-12. Setup
Button Sound
Button Sound
ON
Options are ON
or Off
▼
ENT
9-13. Setup
Device Info
00 IDE0 Master
DVD-ROM:
Reader Model and
Firmware
▼
Press the ▼
button to view
next devices.
ESC
▼
ENT
ENT
YES
01 IDE1 Master
DVDDUAL: NEC
Recorder Model
and Firmware
ENT
ENT
9-14. Setup
System Info
DVD Duplicator
2033S ver: B.123
Fujitsu:29LV1608
2006/06/08 ACARD
▼
9-15. Setup
Quick Erase
All data will be
Does a quick
erase of the disc
Lost, Erase? YES
NO
▼
▼
ENT
YES
9-16. Setup
Full Erase
All data will be
Lost, Erase? YES
Does a full erase
of the disc
ESC
NO
▼
▼
▲
ENT
ENT
ENT
9-17. Setup
Auto Close Tray
Auto Close Tray
Off
Change interval
before tray closes
▼
▼
The Quick Compare feature is not in use.
Setting should remain OFF.
9-18. Setup
Quick Compare
Quick Compare
Off
▼
Available Speeds: Auto, Max,
48x, 40x, 32x, 24x, 20x, 16x,
12x, 10x, 8x, 6x, 4x
▲
▼
9-19. Setup
Audio Burn Speed
Audio Burn Speed
Auto
12
Setup Menu
The Setup menu includes many setting the user can select to customize the use of the QD-
MultiDrive duplicator. Here is a description of the options in the setup menu.
Language
The QD-MultiDrive duplicator has two language options, English and Spanish. English is the
default setting.
CD Burn Speed
The default record speed for the QD-MultiDrive is Maximum (52x). The other record speed
options are: 48x, 40x, 32x, 24x, 16x, 12x, 10x, 8x and 4x.
NOTE: 12x is currently the minimum burn speed. Selecting lower speeds will not
reduce the burn speed below 12x.
Read Speed
The default read speed for the QD-MultiDrive is Maximum (52x). The other read speed
options are:
48x, 40x, 32x, 16x and 8x.
Auto Start Drive
The Auto Start Drive is used to automatically start recording, once the master disc and blank
disc are inserted into the drives.
There are 3 options for this setting, Off, 1 and 2. To use this feature, change the value from
OFF to 1. The 2 setting is not used. Once the value is set to 1, the system will automatically
start recording once a master and blank disc are detected.
Startup Menu
The Startup Menu selection allows you to select the main menu item that appears when the
QD-MultiDrive duplicator starts up. The default setting is 1. Copy. Menu items 1 through 9
can be selected.
Auto Verify
The Auto Verify function can be turned On if you wish to verify every copy you make with the
QD-MultiDrive duplicator. The verify function checks the copied disc, to see if it can be read.
It does not compare the copy with the master disc. The default setting is Off.
Auto Compare
The Auto Compare function can be turned On if you wish to Compare every copy with the
master disc. The Compare function only works with Data master discs. If there is audio or
video on the master disc, the Compare function will not work. The default setting is Off.
Auto Prescan
The Auto Prescan function can be turned On if you with to Prescan every master disc before
recording. The default setting is Off.
Eject Disc
There are 3 options for the Eject Disc setting:
1. Eject good discs only
2. Eject all discs
3. Do not eject discs
The default setting is to eject the good discs only.
Burn Mode
There are 3 options for the Burn Mode setting:
1. DAO (Disc At Once)
2. TAO – Not Close (Track At Once, not closed)
3. TAO (Track At Once, closed)
The default setting is DAO. It is recommended that this setting be used.
13
Display Time
The display time function is used to display the total record time, after the recording is
completed. The default setting is Off.
Button Sound
The Button Sound function is used to turn on or off the beep sound a button makes when
pressed. The default setting is On.
Device Info
The Device Info function displays a variety of information about the CD reader and writer,
including model number and firmware revision. Please review the Setup Menu on page 12
for more details.
System Info
The System Info function displays a variety of information about the controller module,
including model number and firmware revision. Please review the Setup Menu on page 12
for more details.
Quick Erase
The Quick Erase function is used to Erase CD-RW media. This option performs the Quick
erase of the disc.
Full Erase
The Full Erase function is used to Erase CD-RW media. This option performs the Full erase
of the disc.
14
Adv Setup
ENT
ENT
11-01 Adv Setup
Under Run Protect
Under Run Protect
ON
Options are ON or
Off
11. Advanced Setup
▼
▼
▲
▼
ESC
ESC
ENT
ENT
11-02 Adv Setup
Overburn
Overburn
Off
Options are ON or
Off
▼
▲
▼
11-03 Adv Setup
Read Error Skip
Read Error Skip
OFF
Options are ON or
Off
▼
▲
▼
ESC
ESC
ENT
ENT
11-04 Adv Setup
Burn-In
Burn-In
Erase& Copy
Burn-In
Test
To Be Used by
Service Personnel
ONLY
▼
11-05 Adv Setup
Update Firmware
Update F/W A.321
To B.123? YES
Firmware is
updated.
YES
NO
▼
ESC
ESC
ENT
ENT
Adv Setup
11-06
Last update F/W
OK!
Compare Firmware
▼
11-07 Adv Setup
H/W Diagnostics
Runs through
controller diagnostics
▼
ESC
ESC
ENT
ENT
11-08 Adv Setup
Load Default
Load Default
Config? YES
Load Default
OK!
YES
NO
▼
▲
▼
▲
▼
▲
▼
11-09
Options are ON or
Off
Adv Setup
CD+G
OFF
CD+G
▼
ESC
ESC
ESC
ESC
ESC
ENT
ENT
ENT
11-10
Options are ON or
Off
Adv Setup
ISRC & MCN
ON
ISRC & MCN
▼
Options are ON or
Off
11-11
. Adv Setup
USB Option
USB Option
On
▼
▲
▼
Options are ON or
Off
11-12. Adv Setup
CD-Text
CD-Text
On
▼
11-13. Adv Setup
Disc Counter
ENT
ENT
ENT
Disc Counter
View
View disc
counts
▼
11-14. Adv Setup
Update Drive F/W
NOT IN USE
15
Advanced Setup Menu
To get to the Advanced Setup Menu, press and hold the ESC button for three seconds.
The Advanced Setup menu includes options for the more advanced user. Normally these
functions are not used in the daily operation of the QD-MultiDrive duplicator. If you have any
questions about using these functions, please contact the Microboards technical support
department.
UnderRun Protect
The UnderRun Protect feature allows the recorder to use Burn Proof during recording. This
setting defaults to ON and should remain on. This feature protects against making “coasters”
or bad discs. Again, this setting should always remain ON.
Overburn
The default setting for this feature is OFF. Overburn can be used with certain CD recorders,
to allow more data to be writing to the disc. This feature is not supported by the QD-
MultiDrive duplicator.
Read Error Skip
The Read Error Skip feature is used if you wish to ignore read errors during duplication. The
default setting is OFF and it is highly recommended that this setting is not changed. If it is
turned ON, there is the possibility of copying a disc that is not the same as the master.
Burn-in
The Burn-in function is used to test the operation of the QD-MultiDrive duplicator and is for
service purposes only. This function should only be used if directly by Microboards Technical
Support.
Update Firmware
The Update Firmware feature is used to update the controller firmware.
1. To update the firmware: Place the firmware CD into the TOP reader drive.
2. Press the ENT button
3. The display will show:
Update F/W X.12Y
To M.45R YES?
4. Press the ENT button to complete the firmware update.
5. The duplicator will reboot automatically after installing the new firmware.
Compare Firmware
The Compare Firmware function is used to compare the firmware installed on the controller
with the firmware on the CD.
H/W Diagnostic
Hardware Diagnostics runs a number of tests on the controller. Normally this function is used
by service personnel.
Load Default
The Load Default feature will set all the values back to the factory default settings.
16
CD+G
The CD+G feature, when set to ON in the Advanced Setup Menu, will allow you to copy a
CD+G Karaoke master disc. The default setting is OFF.
Important Note: The CD+G value must be set to OFF to use the Track Extraction
feature.
To enable CD+G duplication, perform the following steps:
1. Press and HOLD the ESC button for 3 seconds to enter the Advanced Setup Menu
2. Press the UP or DOWN arrows until the display reads 10-9: Adv Setup CD+G
3. Press ENT to adjust the CD+G setting
4. Use the UP or DOWN arrows to alternate the setting between ON and OFF
5. Press ENT when ON is displayed to enable CD+G duplication
6. Press ESC to exit the Advanced Setup Menu
7. Use the UP or DOWN arrow to return to Copy mode
ISRC & MCN
The ISRC (International Standard Recording Code) & MCN (Media Catalog Number) feature
allows you to copy this information from a CD audio master to the blank disc. The default
setting is OFF.
USB Option
This function is not used in the QD-MultiDrive Series.
CD Text
This feature allows CD-Text content to be copied from master to blank. The default is OFF.
Disc Counter
This feature allows you to view the number of successful and unsuccessful burns. The JC OK
entry is for successful burns for the entire unit; you can also view the individual drive
performance by using the ▼▲ buttons.
Update Drive F/W
This feature is not used by the QD- MultiDrive.
17
Specifications – QD-MultiDrive Series
Model
QD-123
QD-125
QD-127
Recorders
Dimensions, inches (H x W x D)
Weight, lbs
21 lbs
3
5
7
10.5 x 8 x 17
17 x 8 x 18
17 x 8 x 18
33 lbs
37 lbs
•
•
•
•
•
•
Product Interface ATAPI/ IDE
Read Speed 52X
Write Speed 52X
•
•
Firmware Upgrade Via CD-ROM
AC Input: 115/230 VAC; 8/5 AMPS
MAX; 50-60Hz
Maximum Operating Temperature: 25
Degrees C.
•
•
System Display LED
Write Method Auto Detect (DAO, TAO )
Operation Mode COPY, TEST, SCAN,
SAFE
Relative Humidity: 30% - 80% non-
condensing
•
Data Buffer 1 MB
Supported Formats CD-ROM Mode 1 & 2 CD-DA , CD-ROM/XA Video CD , Game CD Mix Mode,
Multisession , HFS CD Bridge , Photo CD , CD Extra, CD+G (Karaoke)
• Recommended Media: Taiyo Yuden
CAUTION: Disconnect AC Power Cord Before Servicing. High Voltages Present with Unit Powered Off and
Line Cord Connected.
Technical Support
For technical questions or support issues, contact Microboards Technology technical support:
United States
PH: 952-556-1639
FAX: 952-556-1628
Europe
PH: +44 (0) 845 230 7800
Japan
PH: 03-3561-2266
Please have the Model and Serial Number of your QD available when contacting
Technical Support.
Any unauthorized modification to this equipment may result in the revocation by the FCC of the user’s
authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and antenna
Connect the equipment into an outlet on a circuit different than that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This product is in conformity with the EMC Directive (89/336/EEC) through compliance with the following European
standards: EN 55022, EN 55024. The CE mark has been affixed in accordance with the CE Marking Directive
93/68/EEC.
Canadian Department of Communications (DOC) Statement
This Class B digital apparatus complies with the Canadian ICES-003 Issue 4:2004. Cet appareil numerique de la classe B est
conforme a la norme NMB-003 du Canade.
18
Appendix 1 List of Functions
1 Copy
2 Test
3 Test & Copy
4 Verify
5 Compare
6 Prescan
7 Disc Info
8 Edit Track
8-1 CD to CD Edit
8-2 Play Audio Track
8-3 Close Session
9 Setup
9-1 Language (Default is English)
9-2 CD Burn Speed (Default is Maximum)
9-3 CD Read Speed (Default is Maximum)
9-4 Auto Start Drive (Default is Off)
9-5 Startup Menu (Default is Copy)
9-6 Auto Verify (Default is Off)
9-7 Auto Compare (Default is Off)
9-8 Auto Prescan (Default is Off)
9-9 Eject Disc (Default is Eject Good Only)
9-10 Burn Mode (Default is DAO)
9-11 Display Time (Default is Off)
9-12 Button Sound (Default is On)
9-13 Device Info
9-14 System Info
9-15 Quick Erase
9-16 Full Erase
10 USB Mode
11 Adv Setup
11-1 UnderRun Protect (Default is On)
11-2 Overburn (Default is Off)
11-3 Read Error Skip (Default is Off)
11-4 Burn-in
11-5 Update Firmware
11-6 Compare Firmware
11-7 H/W Diagnostic
11-8 Load Default
11-9 CD+G (Default is Off)
11-10 ISRC & MCN (Default is Off)
11-11 USB Option
11-12 CD TEXT
11-13 Disc Counter
11-14 Update Drive Firmware (NOT IN USE)
19
Appendix 2 LCD Messages
Normal Conditions:
Initialize SDRAM......................................................................Initialize the memory of the system.
Detect Drives....................................................Detect what drives are connected with the system.
User Abort!....................................................................................Cancel the job during operation.
Analyzing...................................................................................................Analyze the source disc.
Source Drive Not Ready.............................................................Source drive is not ready to read.
Target Drive Not Ready...............................................................Target drive is not ready to write.
Source Disc Not Ready.......................................................... Source disc is not ready to be read.
Target Disc Not Ready.................................................. Target disc is not ready to be written into.
Erasing disc.................................................................The system is erasing the data on the disc.
Fail to get Drive Info!.................................................... The drive information cannot be obtained.
Fail to get Src Disc Info!................................ The information of source disc cannot be obtained.
Save new config Fail!...................................... The new setting of configuration cannot be saved.
Load Default Config?.....................................................Do you want to load the default settings?
Preparing................................................................................... The system is preparing to record.
Check Target Please Wait ............................................The system is checking the target device.
Audio Disc!!! Can’t compare!................................. The system cannot compare the audio discs.
Identical............................................................................... The comparison results are the same.
Read disc error ..........................................................During comparison the disc cannot be read.
Cannot read TOC..................................................... The system cannot read the contents of disc.
TOC not match.............................................................. The comparison results are not the same.
Target overflow.................................... The target disc hasn’t enough capacity to store new data.
Target Disc Not Empty!!!.................................................................. The target disc still has data.
Press a Key to Eject Good Disc……………….Press any key to eject the good disc after
copying.
Press a Key to Eject Fail Disc........................Press any key to eject the failed disc after copying.
CD-RW does not Support the Func.................................... CD-RW doesn’t support this function.
Hold ESC to exit...................................................... Press ESC for a second to terminate the test.
All data will be lost, erase?...............All data on the disc will be lost. Confirm the erasing of data.
Erase Finished..................................................................... The erasing of data comes to an end.
No Erasable Disc in CD-RW!!...........................The disc on the CD-RW device is not rewritable.
Audio Editing:
Lost selected Tracks?................................................. Abort the selected tracks and delete them.
End edit disc and burn?....................................... Finish the music disc editing and start to copy.
Continue edit next Disc?................................. Ask if you want to continue the music disc editing.
Target Overflow Re-Select.............. The disc capacity is not enough to store the selected tracks.
Close all disc’s session?..................................................... Confirm the closing of disc sessions.
NO AUDIO track in this disc.................................................. The source disc has no audio track.
Insert next disc....................................................................................... Insert the next audio disc.
Sessions were closed already!.............................. The disc sessions have already been closed.
Tgt overflow, del last trk?............... The disc capacity is not enough to store the selected tracks.
Ins empty disc Continue?................... Do you want to insert a blank disc and continue copying?
Firmware Update:
Invalid firmware Disc.................................................... The disc doesn’t contain a valid firmware.
Updating F/W.........................................................................The system is updating the firmware.
Update F/W xxx to yyy?................. Do you want to update the firmware version from xxx to yyy?
Searching F/W ......................................................... The system is searching for a valid firmware.
Check Sum Error!...................................................................... The updated firmware has errors.
Last update F/W OK!........................................................... The firmware is updated successfully.
Last update F/W Fail!.................................................... The firmware is not updated successfully.
Flash ROM fail!................................................................. Data cannot be written into Flash ROM.
7/2008
21
|
Land Pride Lawn Mower HR15 User Manual
Leupold Home Safety Product Alumina User Manual
LG Electronics Marine Instruments 25UM64 User Manual
LG Electronics Refrigerator LPXS30866D User Manual
Linear Satellite Radio XR D User Manual
Manitowoc Ice Ice Maker 7620283 R12 400 User Manual
Maytag Range MGR6775 User Manual
MB QUART Headphones Headphone Headset User Manual
Melissa Kitchen Grill 643 051 User Manual
Memorex MP3 Player MMP8560 User Manual